AMSCM 5A Low Dropout Voltage Regulator FEATURES. Three Terminal Adjustable or Fixed V, V and V Output Current of 5A Operates Down to. the end of the datasheet. Typical Application. 1. An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in. The AIC is a low dropout three terminal regulator with 5A output current capability. The output voltage is adjustable with the use of a resistor divider or fixed.

Author: Fenrile Vinos
Country: Cape Verde
Language: English (Spanish)
Genre: Science
Published (Last): 10 October 2012
Pages: 111
PDF File Size: 10.97 Mb
ePub File Size: 10.60 Mb
ISBN: 999-5-90484-685-9
Downloads: 19268
Price: Free* [*Free Regsitration Required]
Uploader: Kagagar

Once the devices power is determined, the maximum allowable? Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.

Datasheet search «AMS*»

The higher the thermal resistance, the hotter the IC. The adjustable versions allows an additional capacitor to be used at the ADJ pin to increase ripple rejection.

However after careful reading of the datasheet it turns out that all that would happen is it would read close to max value of so all is good. Thermal Considerations ICs heats up when in operation, and power consumption is one factor in how hot it gets.

The junction temperature can be predicted as follows: Refer to Overload Recovery in Application Notes. Posted in Projects on May 7th, PCB Date is 14th January Posted in Projects on Jul 27th, National Semiconductor Corporation Americas Email: Posted in Teardowns on Aug 22nd, The topology is basically that of the LM except for the pass transistor. Also I could use this to display the time as datxsheet LED matrices are just enough to fit the time, e.


C for the output section.

All numbers apply for packages soldered directly into a PC board. The adjust pin can take a transient signal of?

CM-X pdf Datasheet P1 Part Num IC-ON-LINE

Pobierz plik – link do postu. It is also available in three daatasheet voltages: Refer to curve section for the short circuit current vs.

The reason for the 2 diodes was to protect against high input voltages because I believed that if we exceeded the 1. Testing the 4 motors all at once at different voltages gave me the following current draw results — 1.

JA max is calculated as: In order to get the total resistance to ambient? This series resistance introduces a zero within the loop to increase phase margin and thus increase stability. Continued than the VOUT by the sum of the voltage drops along the line resistances. Posted in Projects on Apr 29th, In this case, an external diode is recommended between the output and input pins to protect the regulator, shown in Figure 5.

PCB date code is Nov The structure of the pass transistor is also known as a quasi LDO. This constant current then flows through R2. This results in a lower dropout voltage.

AMSCM Datasheet pdf – 5A LOW DROPOUT VOLTAGE REGULATOR – Advanced Monolithic Systems

Life support devices or systems are devices or systems datqsheet, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.


The adjust terminal can be bypassed to ground with a capacitor CADJ. If I were to re-do this project I would have laid out the PCBs better so they could just connect to each other without wires. This solar charger might use PWM to charge the battery which means the solar panels voltage would directly be applied to the battery for a certain amount of time, it would probably be more efficient than using a DC-DC or transistor to step it down but not the best if something does go wrong.

The fixed versions intergrate the adjust resistors. The DisplayPort connector is directly wired and glued, not too bad. Posted in Teardowns on Jul 14th, Figure 3 shows a typical application using a fixed output regulator. We easily pop out the covers on each end. C Line Regulation 0. Life support devices or systems are devices or systems which, I are intended for surgical implant into ddatasheet body or ii support or sustain life, and whose failure.

When adjusted for voltages higher than VREF, the ripple rejection decreases as function of adjustment gain: C for the control section, while TJ max is ? CH and one for heatsink to ambient? Power dissipation is kept in a safe range by current limiting circuitry. Therefore a 5V adjustment decreases ripple rejection by a factor of four dB ; Output ripple increases as adjustment voltage increases. If the case is soldered to the heat sink, then dattasheet