EEPROM 95160 PDF

STMicroelectronics MW Series EEPROM are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for STMicroelectronics . Errors and solutions here for eeprom read/write with Carprog programmer: Error 1: “ID not found” when read eeprom EEPROM, Serial SPI, 16 Kbit, 2K x 8bit, 10 MHz, SOIC, 8 Pins The M WMN6P is a 16Kbit (2K x 8bit) serial SPI bus EEPROM (Electrically Erasable.

Author: Zololkis Gazuru
Country: Burma
Language: English (Spanish)
Genre: Politics
Published (Last): 28 October 2017
Pages: 324
PDF File Size: 13.36 Mb
ePub File Size: 12.88 Mb
ISBN: 177-7-20727-114-7
Downloads: 61712
Price: Free* [*Free Regsitration Required]
Uploader: Shaktill

MCUmall EPROM BIOS Chip Burner Forum – 8pin

Reply 13 benaknoun Spain Posts. Which part number you selected in software? Reply 5 ZLM Posts. That is safe and fastest way.

Then the ADP should be used. Reply 15 ZLM Posts.

But the fast way is to remove it from board and program it on the programmer ZIF spcket directly. The “Device blank check failed ” means the chip is not a blank chip, there are some data in the chip. Chip is blank eeporm this mean this chip is empty???

The only way to test data is: Try to power up the board and do not connect pin 8 Vcc pin. Reply 2 benaknoun Spain Posts. Reply 16 benaknoun Spain Posts.

  DISYUNCION CROMOSOMICA PDF

Hi, i have received the tools i bought from mcumall canada, there are numbers on the adapters, how do i know which pin is the right matching one with the chip? All other pins are pin to pin connect to programmer socket. I believe they will do the job.

Reply 1 95610 Posts. Reply 6 benaknoun Spain Posts. Hi, it seems i’m doing something right then! Reply eepeom benaknoun Spain Posts. Use ToolA instead, because your chip pins already damaged. Hi, i have connected the tool to the chip and adapter to the programmer. Reply 17 ZLM Posts. Reply 10 benaknoun Spain Posts. What is exact part number? So, if you can not read anything out, make sure your pins have good contacting.

Carprog 9.31 reads/writes eeprom 95160 with A4/A6 adapter

To be honest though, the other adapter i bought, not sure what its for?? Reply 8 benaknoun Spain Posts. Also, another question please about the same chip: Device blank check failed at address: You need to find a way to test the data.

If it is “”, then it has no ID on this chip. Once the chip is blank, then you can load your data file and click on Write button to wrtie the data into chip. When you uploading eeproom image, only use letter and number as file name. Reply 19 ZLM Posts. Reply 11 benaknoun Spain Posts.

  DIBS EM BUSCA DE SI MESMO PDF

You can save data as.

If the chip is not designed for programming in circuit, then you need to try to find some connection. It is SOIC8 mil chip. Reply 7 ZLM Posts. Reply 18 benaknoun Spain Posts.

Most of used 91560 chips should have something. Hi, ok forget this chip, its damaged That is depending on your circuit design.

What is your chip on board? Also, when i click on ID, it says “function eepgom supported on this device” Image Insert: I think it should be SOIC8 mil chip.

Carprog reads/writes eeprom with A4/A6 adapter | OBDIIcom Official Blog

Reply 14 benaknoun Spain Posts. It should be able to open it by same software. Reply 3 ZLM Posts. Reply 9 ZLM Posts.

Hi, thanks for your reply, here are the numbers on the chip: What is your another adapter part number? The wire can be any wires, as long as you can solder it. Reply 12 ZLM Posts.